A commercial washing machine can cost up to $3,000. With such an expensive piece of equipment, you’ll want to ensure that you take good care of it so that you won’t have to worry about buying a new one.
To ensure that your commercial laundry equipment runs properly, it’s essential to do regular maintenance.
But what happens if your expensive washer does break? Keep reading to discover what problem you might be experiencing and what you can do about it.
Common Washing Machine Problems
If you’re working with some older washing machines or don’t have a warranty, you’ll first want to diagnose what the problem is. This will help you figure out if it’s worth it to call a company or not.
Some of the most common problems include:
- Not starting
- Excessive noise
- Water leaking
These signs are just symptoms of a deeper problem, which could be anything. If you have experience with the machines, you might be able to replace a few parts here and there, but if the problem seems to be worse, you may need to call in a repair company.
Not Filling With Water
For example, if your washer isn’t filling with water, you’ll want to look at the inlet hose. You’ll need to see if the hose is damaged or if there is just a kink in it.
If there’s a leak, you can install a temporary patch rather than replace the entire hose. However, if you’re going to install a new hose, make sure that you keep it as straight as possible so that this problem doesn’t happen again.
Tub Won’t Spin
Before you check other machine parts, you must first adjust the load. There are too many clothes in there, making it harder for the drum to spin.
You should also check to see if the lid safety switch is on. This is generally underneath the main top with a protective lid. The switch will supply power to the motor and timer, and it’ll activate when you close the lid.
You could have a tripped switch that needs to be connected or replaced.
Water Won’t Stop
Maybe you turned the washer on, and then the water didn’t stop running out. This could be an issue with the overflow switch, which will detect if the tub is full and stop the water flow.
Before installing a replacement, you should check to see if the switch is disconnected.
On the flip side, if the water stops but won’t drain, you likely have an issue with your drain pump. Your washer won’t go toward the next cycle if the water doesn’t drain.
You should check if any small items are inside the drain pump. If it’s clogged, you’ll need to buy a replacement.
Set a Maintenance Routine
If you want to prevent some of those problems from starting, you should look into commercial laundry equipment maintenance. When you have a regular maintenance schedule, you’ll be taking one more step towards ensuring that it doesn’t break down.
You should develop a schedule and ensure that your crew stays on track. Create a checklist to make sure that you don’t forget anything.
If you aren’t sure what to do, ask a trusted maintenance company what they would recommend. Your laundry manual may also have important information about the requirements and specific cleaning steps that you should take care of.
Commercial Laundry Solutions
If your manual doesn’t have any suggestions on maintenance to keep your machine running, you should start with cleaning the exterior of the laundry equipment.
The clean equipment will help remove any debris or lint from getting into your machine, clogging it, and causing it to break. You should also have regular cleaning to prevent detergent or soap from damaging the machine.
Speaking of soap, also clean out the dispensers. The powder and soap can easily clog it up, making your machine inoperable. You should clean them out regularly and soak them in water. If they clog up, you’ll need to pay to replace them.
You’ll also want to check the seal outside your washer doors. You’ll need to remove buildup around the seals to make sure your equipment won’t end up leaking any of the water out. If water is leaking, you may need to check that the seal isn’t loose.
You’ll also want to check the inlet and outlet hoses regularly. These hoses can build up sediment, and when it builds up, your machine can leak. Inspecting these can also ensure that you lower your water bills and prevent a bigger disaster later on.
Find a Repair Company
If your equipment does break, you’ll need commercial laundry equipment repair. Sometimes the job is too big for you to fix or needs specialized care.
You won’t have to worry about your machines not running for a while when you have trusted technicians working to solve the problem. It would be best to do your research to find a reliable company that can offer quick services so that you don’t impact your customers.
You may also want to find a company that can help you with the maintenance. They can develop the perfect maintenance plan to keep your machines running so that you don’t have to worry about it.
Discover More About Commercial Laundry Equipment Repair
These are only a few things to consider for commercial laundry equipment repair, but many other problems might crop up.
If you’re experiencing any of these issues (or more) and want to find someone who can take care of it for you, contact Laundry South, and we can come out and take a look at your machine.